K639A Mast Section For Tower Crane Masts

  • K639A Mast Section For Tower Crane Masts
  • K639A Mast Section For Tower Crane Masts
  • K639A Mast Section For Tower Crane Masts
K639A Mast Section For Tower Crane Masts
  • ZCJJ
  • China
  • 10days
  • 50pcs

Manama Tower crane service
Cairo Tower crane service, Alexander Tower crane service
Port Said Tower crane service, Suez Tower crane service

Products Specification

Type , Model: K639A Mast Section For Tower Crane Masts

Size: 2mx2mx5m 

Materials: Q345B

Within: Pins, bolts, Ladder, Platform

Process: Blasting derusting, 

Painting:  Under painting , Middle painting, Surface painting.

Our factory produce and supply almost all famous brand tower crane :Mast section, Anchor Frame, Fixing angle ,Adaptor and so on as good quality and price.

K639A Mast Section

K639A Masts

 

 

2m K Mast Section

 

K639A Mast Section For Tower Crane Masts

 

Tower Crane Knowledge sharing:

A Simple Method for Differentiating the Quality of Hydraulic Oils without Special Detection Instrument


3 Identification of the change of viscosity of hydraulic oil
(1) Glass plate tilt method: Take a clean glass plate, place it horizontally, drop a drop of the tested hydraulic oil on the glass, and drop a drop of the standard hydraulic oil(the same brand of new hydraulic oil next to it. Then tilt the glass plate and pay attention to the observation

 If the flow rate and flow distance of the measured oil fluid are larger than that of the Standard Oil fluid, the viscosity is lower than that of the Standard Oil fluid, and conversely, the viscosity is higher than that of the Standard Oil fluid.
(2) The glass bottle inversion method: Put the tested hydraulic fluid and standard fluid in two transparent glass bottles of the same size and length(do not fill up too much), and use the plug to block the two bottles. Place the two bottles side by side, and then quickly reverse the two bottles at the same time.

 

K639A Mast Section For Tower Crane Masts

 If the bubbles of the tested hydraulic oil in the bottle rise faster than the bubbles of the Standard Oil fluid in the bottle, the viscosity of the oil fluid is lower than the viscosity of the Standard Oil fluid. Conversely, the viscosity of the oil fluid is higher than the viscosity of the Standard Oil fluid. If the two oil bubbles rise at a similar rate, the viscosity is similar.
4 Identification of variation of hydraulic oil quality
(1) Identification of oil fluid from the oil pump: If a small amount of oil fluid is removed from the oil pump and it is found to be milky white(sometimes like pale yellow milk), and when identified by the combustion method, it is found to contain a large amount of water. The loss of viscosity by hand indicates that the oil has been completely emulsified and deteriorated and is not suitable for further use.

 

K639A Mast Section For Tower Crane Masts

 

 

(2) Identification of the oil in the fuel tank: Remove a little of the tested oil from the fuel tank and filter it with filter paper. If there is a black residue on the filter paper and there is a pungent odor, it indicates that the oil has been oxidized and deteriorated. It is also possible to remove some of the precipitated sludge directly from the bottom of the fuel tank. If it is found that there is a lot of asphalt and colloidal precipitation, put it on the finger and pinch it. If the colloidal is felt, the adhesion is strong. The process of eliminating a hydraulic oil pollution failure was introduced, and measures were drawn up to prevent the failure from happening again. During a fall of the H3/36B building tower crane, the third trip was performed. Suddenly, the hydraulic cylinder is unable to rise, and the piston rod has only a very small extension.

At the same time, the accompanying phenomena are:
(1) Hydraulic system makes a sharp and loud sound
(2) Hydraulic tubes produce intense high-frequency vibrations

 

K639A Mast Section For Tower Crane Masts

(3) A significant increase in temperature can be felt by touching the hydraulic tube by hand.
The hydraulic overhead system of the H3/36B building tower crane is relatively simple. There is only one overhead hydraulic cylinder. The high-pressure oil output from the hydraulic pump is directly input into the hydraulic cylinder, and there is a overflow loop on the main oil road. After understanding, the hydraulic oil in the fuel tank is a newly replaced hydraulic oil that was newly replaced four months ago when the top lift was added.
After analysis, we believe that the reasons for the failure may include:
(1) Damage leakage of hydraulic pump(2) Internal leakage caused by damage to hydraulic cylinder sealing device.
After stopping the hydraulic pump, the hydraulic cylinder was observed and no piston rod was found to retract, eliminating the possibility of leakage in the hydraulic cylinder. After the oil tank cover was opened for inspection, no damage was found to the hydraulic pump.

K639A Mast Section For Tower Crane Masts

 

However, it was found that the filter core surface of the filter was adsorbed with a layer of fluff and a small amount of fine sand. The hydraulic system returned to normal after the fluff and fine sand were removed. It is further understood that when the oil was changed last time, the maintenance staff cleaned the fuel tank with cotton yarn to wipe the inner wall of the fuel tank. Therefore, a lot of cotton yarn remains on the inner wall of the fuel tank, causing pollution of the new hydraulic oil. When the contaminated hydraulic oil continues to pass through the filter, the fluff is filtered on the filter core, causing serious blockage of the filter core and emptying of the hydraulic pump.
After the analysis of this failure, we made the following requirements for the maintenance of the hydraulic system in the future:

K639A Mast Section For Tower Crane Masts

(1) Hydraulic oil should be replaced regularly. Before replacing hydraulic oil, clean the fuel tank first. Do not wipe the inner wall of the tank with cotton yarn, cotton cloth and other items that are prone to falling fibers. Use silk cloth or vinyl resin sponge

(2) Timely cleaning or replacement of filters
(3) During maintenance, no hydraulic element shall be removed and placed directly on the ground.




 

 

 

Get the latest price? We'll respond as soon as possible(within 12 hours)

Privacy policy

close left right